If your Whirlpool refrigerator isn’t working the way it should, you may need to reset it. When a Whirlpool refrigerator fails to operate properly, it’s usually due to a minor software glitch or an issue with its sensor. Resetting your Whirlpool refrigerator is quick and easy and can be done in just a few minutes with very little effort. If you follow the steps below, you can get your Whirlpool refrigerator up and running smoothly again in no time at all. Resetting your Whirlpool refrigerator is also helpful if it has locked you out by registering too many failed login attempts. In this case, you will need to enter factory settings so that you can log back in with a new password.
How To Reset Your Whirlpool Refrigerator?
1. Clear the Ice and Water
Turn off your Whirlpool refrigerator at the power switch. Then unplug it.
2. Remove the Door Gasket
Remove both of the screws that hold on the door gasket to remove it from your Whirlpool refrigerator. Then throw it away or recycle it at a local recycling center. You can also clean off any dirt or debris that is stuck to the gasket with a wet sponge and warm water. When you are done, clean off all of the dust that is on your Whirlpool refrigerator with a dry cloth or soft brush before putting everything back together again.
3. Remove the Door Panel
Pull out both of the screws that are holding down your Whirlpool refrigerator’s door panel and remove them from your appliance. Then take out any other screws that secure your Whirlpool refrigerator’s door panel in place, such as around its hinges, with a screwdriver if necessary to help you remove it from its housing unit so that you can access its circuit board inside of it for resetting purposes later on in this process.
4. Remove the Circuit Board
To reset your Whirlpool refrigerator’s circuit board, you will need to remove it from its housing unit. This is a very easy task that only takes about 15 seconds. Once you have removed it from its housing unit, you can now connect a screwdriver to your Whirlpool refrigerator’s circuit board’s terminals and carefully turn them both counterclockwise to reset the software on your Whirlpool refrigerator.
5. Reset the Software
You will need to reset the software on your Whirlpool refrigerator by turning the two wires that are connected to its circuit board’s terminals clockwise so that they are connected together again and then reconnecting them back into their respective places at this point in this process as well as after installation has been completed successfully.
What To Do Before Resetting Your Whirlpool Refrigerator
1. Back Up your Whirlpool Refrigerator’s Data
Back up your data in case you need to do a factory reset on your Whirlpool refrigerator. You can do this by connecting your Whirlpool refrigerator to a computer and loading up its memory with the data that you want to store. For more information on backing up data, please refer to the instructions included with your Whirlpool refrigerator or refer to our article titled “How to Back Up Your Data in Your Whirlpool Refrigerator” for more information.
2. Remove Water from the Refrigerator
To remove all of the water from the inside of your Whirlpool refrigerator and prevent it from leaking when you restart it after completing this process, turn off the water supply and drain out any water that is inside of it using a sink strainer or any other means possible.
Why Is My Whirlpool Refrigerator Displaying An Error Message?
1. Check the Power cord
If your Whirlpool refrigerator is not turning on, you will want to check the power cord to make sure it is securely connected properly. If it is not, then you will need to go through this process again with a new one until the problem has been resolved.
2. Check the Temperature Sensor
If your Whirlpool refrigerator is not turning on, you will want to check whether or not its temperature sensor has been damaged. This will allow you to determine if it needs a new one or if that sensor simply needs cleaning and calibration as well before attempting to reset its software again. You can read more about this in our article titled “How to Clean and Calibrate Your Whirlpool Refrigerator’s Temperature Sensor” for more information about how you can do so successfully.
3. Check the Voltage
If your Whirlpool refrigerator is not turning on, you will want to check the voltage on it to make sure that it has a sufficient amount of power. This will allow you to determine if it needs a new one or if that voltage simply needs cleaning and calibration as well before attempting to reset its software again. You can read more about this in our article titled “How to Clean and Calibrate Your Whirlpool Refrigerator’s Voltage Sensor” for more information about how you can do so successfully.
4. Check the Power Cord
If your Whirlpool refrigerator is not turning on, you will want to check the power cord to make sure it is securely connected properly. If it is not, then you will need to go through this process again with a new one until the problem has been resolved.
5. Check the Voltage
If your Whirlpool refrigerator is not turning on, you will want to check the voltage on it to make sure that its power supply has a sufficient amount of power. This will allow you to determine if it needs a new one or if that voltage simply needs cleaning and calibration as well before attempting to reset its software again. You can read more about this in our article titled “How to Clean and Calibrate Your Whirlpool Refrigerator’s Voltage Sensor” for more information about how you can do so successfully.
Why Do You Need To Reset Your Refrigerator
1. The Refrigerator has a Bad Control Board
If your Whirlpool refrigerator is not turning on, you will want to check whether or not its control board has been damaged. This will allow you to determine if it needs a new one or if that control board simply needs cleaning and calibration as well before attempting to reset its software again. You can read more about this in our article titled “How to Clean and Calibrate Your Whirlpool Refrigerator’s Control Board” for more information about how you can do so successfully.
2. The Refrigerator has a Bad Power Supply
If your Whirlpool refrigerator is not turning on, you will want to check whether or not its power supply has sufficient power. This will allow you to determine if it needs a new one or if that power supply simply needs cleaning and calibration as well before attempting to reset its software again. You can read more about this in our article titled “How to Clean and Calibrate Your Whirlpool Refrigerator’s Power Supply” for more information about how you can do so successfully.
3. The Refrigerator has a Bad Temperature Sensor
If your Whirlpool refrigerator is not turning on, you will want to check whether or not its temperature sensor has been damaged. This will allow you to determine if it needs a new one or if that temperature sensor simply needs cleaning and calibration as well before attempting to reset its software again. You can read more about this in our article titled “How to Clean and Calibrate Your Whirlpool Refrigerator’s Temperature Sensor” for more information about how you can do so successfully.
4. The Refrigerator has a Bad Cooling Fan
If your Whirlpool refrigerator is not turning on, you will want to check whether or not its cooling fan has been damaged. This will allow you to determine if it needs a new one or if that cooling fan simply needs cleaning and calibration as well before attempting to reset its software again. You can read more about this in our article titled “How to Clean and Calibrate Your Whirlpool Refrigerator’s Cooling Fan” for more information about how you can do so successfully.
4. The Refrigerator has a Bad Door Lock/Door Switch
If your Whirlpool refrigerator is not turning on, you will want to check whether or not its door lock/door switch has been damaged. This will allow you to determine if it needs a new one or if that door lock/door switch simply needs cleaning and calibration as well before attempting to reset its software again. You can read more about this in our article titled “How to Clean and Calibrate Your Whirlpool Refrigerator’s Door Lock/Door Switch” for more information about how you can do so successfully.
Conclusion
If your Whirlpool refrigerator isn’t working the way it should, you may need to reset it. When a Whirlpool refrigerator fails to operate properly, it’s usually due to a minor software glitch or an issue with its sensor. Resetting your Whirlpool refrigerator is quick and easy and can be done in just a few minutes with very little effort. If you follow the steps below, you can get your Whirlpool refrigerator up and running smoothly again in no time at all. This guide also provides information on what to do when you see an error code, how to troubleshoot common issues, and what to do if your refrigerator has locked you out.
FAQs:
Q. What do I need to do before resetting my Whirlpool refrigerator?
- The first thing you’ll want to do is check the power on your Whirlpool refrigerator. If it does not turn on, or if the voltage is low, then you will need to replace its power cord.
Q. How can I tell if my Whirlpool refrigerator has a software glitch?
- When your Whirlpool refrigerator doesn’t work properly, it usually means there is a minor issue with its software that needs to be addressed first before resetting it can fix the problem. To determine this, start by checking if there are any error codes that appear on the screen or display screen when you try to turn your Whirlpool refrigerator on and off again. If there are any error codes present, this means that there is probably an issue with the code itself and not with your actual defrost timer or heating elements themselves.
Q. What should I do if my Whirlpool refrigerator has locked me out?
- If your Whirlpool Refrigerator has locked you out of its settings menu, then this means that it has stopped responding to its controls because of some sort of malfunction in either the control panel or within its software itself which must be fixed before trying again to reset it again as described in our article titled “How to Reset Your Whirlpool Refrigerator” for more information about how you can do this.
